Product Description

A flange isolation kit has three dielectric barriers, and the sleeve is the one that goes through the hole. The central gasket isolates the flange faces. The G10 insulation sleeve slides over each stud bolt and fills the annular gap between the bolt and the flange bore — without it, the bolt shank touches the flange hole and the cathodic protection circuit grounds through the fastener. Kaxite manufactures NEMA LI-1 G-10 sleeves from epoxy-impregnated woven glass tube: 1/32″ standard wall, 8–800 mm diameter range, ≥400 V/mil sleeve-grade dielectric strength, 130–150°C continuous. Standard sizes ship in 5–10 days; custom diameters cut from 500 pieces per size.

Product Detail

G10 Insulation Sleeve Manufacturer — Flange Kit Bolt Isolation Tube, NEMA G-10, 1/32″ Wall, Custom Diameters

The Second Dielectric Barrier — the Tube That Goes Through the Hole

Gasket on the Faces. Washers Under the Nuts. Sleeve Through the Hole.

A flange isolation kit has three dielectric barriers, and the sleeve is the one that goes through the hole. The central gasket isolates the flange faces. The G10 insulation sleeve slides over each stud bolt and fills the annular gap between the bolt shank and the flange bolt hole — without it, the bolt touches the flange bore and the cathodic protection circuit grounds through the fastener. The washer under the nut does not compensate for a missing sleeve; it is a separate barrier at a separate contact point. In a fully insulated joint, all three must be present. The sleeve is not an accessory. It is the component that makes the bolt hole a dielectric gap instead of a conductive path.

G10 insulation sleeve for flange isolation kit, NEMA LI-1 G-10 bolt isolation tube, 1/32 inch wall, Kaxite manufacturer
G10 insulation sleeve — NEMA LI-1 G-10, 1/32″ standard wall for flange-kit service.

G10 Sleeve vs Mylar Sleeve — Material Choice in a Flange Kit

Dimension G10 Glass Epoxy Sleeve (this page) Mylar (PET) sleeve
Compressive strength 50,000–65,000 psi (grade dependent) Not a load-bearing material; lower compressive resistance
Continuous temperature 130°C–150°C (grade/data sheet dependent) ≈105°C–120°C (PET limit)
Water absorption 0.09%–0.4% (test method dependent) Low, but dimensional stability under load is lower
Sleeve-grade dielectric strength ≥400 V/mil per industry specification Sufficient for basic isolation; lower mechanical support
Best for High bolt load, higher temperature, long service, cathodic protection systems Standard pressure, cost-sensitive kits, low bolt load

The sleeve sits inside the bolt hole and the bolt load passes through it only as a radial constraint, not as a compressive column — but the sleeve must maintain its wall thickness and dielectric integrity under vibration and thermal cycling. G10 holds wall thickness and dielectric strength under those conditions. Mylar is a valid cost-down option for low-pressure, low-temperature kits, but it is not the material to specify when the joint is under cathodic protection or high bolt load. For the complete kit where the sleeve is supplied with a G10 or phenolic gasket, see Type E full-face isolation kits or Type F raised-face kits.

Technical Data — NEMA LI-1 G10 Sleeve Tube

Material Electrical-grade epoxy resin with woven glass fabric, laminated tube
Standard NEMA LI-1 G-10; ASTM D709 G-10
Standard wall thickness 1/32″ (approximately 0.8 mm)
Diameter range 8 mm to 800 mm
Wall thickness range From 0.5 mm
Maximum tube length 12 m
Sleeve-grade dielectric strength ≥400 V/mil per industry specification; batch data sheet on request
Compressive strength (G10 grade) 50,000–65,000 psi (grade dependent)
Water absorption 0.09%–0.4% (test method dependent)
Continuous operating temperature 130°C–150°C (grade and data sheet dependent)
Insulation resistance 5 × 10⁴ MΩ (KLINGER Type S G10 data)

The G10 sleeve is one component in a complete isolation kit. For the matching G10 washer under the nut, see G-10 glass epoxy washer. For the full kit range, see flange insulation gasket kits.

Sleeve Length and Diameter — What to Specify

The sleeve is not a catalog tube cut to any length. Its length is set by the joint stack-up: the sleeve must extend through the flange bolt hole and into the insulating washer on each side, typically one and one-half washer thicknesses on each side of the flange. The inside diameter must clear the stud or bolt; the outside diameter must fit the flange bolt hole with the specified wall thickness (1/32″ standard). State the bolt/stud size, the flange bolt hole diameter, and the washer thickness at inquiry. Custom diameters from 8 mm to 800 mm and custom lengths are cut to order; standard bolt sizes ship in 5–10 days. For a complete kit where the sleeve dimensions are already matched to the gasket and washers, see the VCS very critical service kit.

Applications — Where the G10 Sleeve Is Specified

The G10 sleeve is the standard bolt-hole barrier in flange isolation kits for cathodic protection systems, where the bolting must be electrically isolated from the flange bore to prevent the protection current from grounding through the fastener. It is also specified for galvanic corrosion isolation between dissimilar metal flanges, replacement sleeves for existing kits, and any bolted joint where a non-conductive tube must maintain its wall thickness under vibration and thermal cycling. For a comparison of the sleeve with the washer and the central gasket, see the G-10 washer page and the Type E kit page.

MOQ, Lead Time and Ordering Specification

Standard bolt sizes: ship in 5–10 days. Custom diameters and lengths: 10–20 days. Custom cut MOQ: 500 pieces per size. OEM and wholesale pricing applies for volume orders. To quote correctly, specify: bolt/stud size or ID × OD × length, quantity per size, whether the sleeve is a standalone replacement or part of a complete kit, and any standard or drawing requirement (NEMA LI-1 G-10 / ASTM D709 G-10). This is a machined tube, not a catalog part — the more precisely the dimensions and the joint stack-up are stated, the faster the quotation.

Buyer FAQ

What does the G10 sleeve actually do in a flange insulation kit?
It slides over each stud bolt and fills the annular gap between the bolt shank and the flange bolt hole. Without it, the bolt touches the flange bore and the cathodic protection current grounds through the fastener — the sleeve is the dielectric barrier at the bolt hole, separate from the gasket at the flange faces and the washer under the nut.
G10 sleeve vs Mylar sleeve — which should I use?
G10 for high bolt load, higher temperature (130–150°C), cathodic protection systems and long service life. Mylar is a cost-down option for low-pressure, low-temperature kits where bolt load and thermal cycling are modest. G10 maintains wall thickness and dielectric strength under vibration and thermal cycling; Mylar is not the material to specify when the joint is under cathodic protection.
What is the standard wall thickness for a flange-kit G10 sleeve?
1/32″ (approximately 0.8 mm) is the flange-kit standard. Custom wall thicknesses from 0.5 mm are available for non-standard bolt holes or specific dielectric requirements.
How is the sleeve length determined?
The sleeve must extend through the flange bolt hole and into the insulating washer on each side — typically one and one-half washer thicknesses on each side of the flange. The length is set by the joint stack-up, not by the tube’s stock length. State bolt size, bolt hole diameter and washer thickness.
What standard does the G10 sleeve meet?
NEMA LI-1 G-10, equivalent to ASTM D709 G-10. Sleeve-grade dielectric strength per industry specification is not less than 400 V/mil; batch material certificates are available on request.
What is the MOQ for custom-cut G10 sleeves?
500 pieces per size for custom ID/OD/length. Standard bolt sizes have no custom-cut MOQ and ship in 5–10 days. OEM/wholesale pricing applies from the first order for standard sizes.

Send bolt/stud size or ID × OD × length, quantity, and whether this is a standalone replacement or a complete kit requirement. Engineering team confirms material grade, wall thickness and lead time.

Request G10 Sleeve Quotation

Products Categorys

Featured Products

Navigation